Notice The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of the product, be that either d
P. 10 Installation Guide the relay is activated, +12 volts from 87 is sent through 30, and the OEM trunk switch is activated, by the positive pulse.
Installation Guide P. 11 module's Trunk release output activates the relay. The ground signal is sent from 87 through 30 to the vehicle's Tr
P. 12 Installation Guide 5-pin Secondary Harness (a.k.a. the secondary harness) This harness has the remaining wires used in basic remote starter ins
Installation Guide P. 13 6 VIOLET (+) Door pin input This input should be used in vehicles that use a positive-switching Dome Light circuit. Connect t
P. 14 Installation Guide If no Glow-plug wire is found on the vehicle, the Glow-plug input on the module may be “timed out”. The module will power up
Installation Guide P. 15 Note: To exit programming mode, close the hood. Note: To exit programming mode, press on the antenna button once (the LED wi
P. 16 Installation Guide To install this unit in a vehicle with an automatic transmission: 1. Cut the loop on the pc board (Yellow wire). 2. Make s
Installation Guide P. 17 FEATURE 4 – Door lock pulse timing OPTION 1* 7/10-sec. lock / unlock pulses OPTION 2 4-sec. lock / unlock pulses OPTION 3
P. 18 Installation Guide 3. Press the Ι button if you wish to increase the time delay or the ΙΙ button if you want to decrease it. The time delay wil
Installation Guide P. 19 Clutch Bypass In order to remote start a manual transmission vehicle, the clutch switch must be bypassed. Clutch safety sw
P. 2 Installation Guide Table of ContentsIntroduction ... 2 Included in the Kit...
P. 20 Installation Guide modules connected to the G.O. Wire, a relay (and diodes) may have to be added to strengthen the negative current going to the
Installation Guide P. 21 Starter Kill Arming Mode Note: It can only be activated if button Ι is programmed as LOCK or UNLOCK button. The Starter Ki
P. 22 Installation Guide Bypass Remote starters of this series offer three possibilities for bypass D2D: they are compatible with Trilogix, ADS and Fo
Installation Guide P. 23 To enter Cold Weather Mode: • Press and hold the ΙΙ button for 3 seconds or until the parking lights flash three (3) time
P. 24 Installation Guide c. Press the push button switch until the Parking lights flash twice. d. Release the push button and turn the ignition to t
Installation Guide P. 25 transmitter. The parking lights will flash 3 times quickly and remain lit. 4. Remove the key: the engine will continue ru
P. 26 Installation Guide OEM alarm control. Make sure the module is able to arm and disarm the oem alarm (if applicable). Door locks and trunk t
Installation Guide P. 27 Diagnostics – Parking Light Flash Table Flashes Description 1 • Doors locked, starter kill armed • Run time has expire
P. 28 Installation Guide Troubleshooting Q & A The following are some common installation-related issues. A problem or symptom is given and then p
Installation Guide P. 29 • Do you have the correct OEM disarm wire? • Did you program the disarm wire? 11. The ABS and the CHECK ENGINE light co
Installation Guide P. 3 Included in the Kit Before beginning the installation, please review the Installation Guide —particularly the Wiring Diagram a
P. 30 Installation Guide 25. I blow fuses every time I try the remote door locks and I have already installed a relay. • Door locks are reverse pola
P. 4 Installation Guide ♦ When wiring in parallel, make sure to isolate each connection with a diode in order to avoid feedback and possible damage.
Installation Guide P. 5 Installation Order The following is a suggested order for the Installation procedure. It is intended as a guide for novices, t
P. 6 Installation Guide when the module is in the vehicle. The fuses on the power wires should be removed during the pre-wire stage. The fuses will n
Installation Guide P. 7 A basic introduction to the Relay What is a relay? A device that responds to a small current or voltage change by activating s
P. 8 Installation Guide quenching/suppression diode, and that the Negative trigger is on the same terminal of the relay as the Anode (+ or non-stripe
Installation Guide P. 9 Problem: Some vehicle circuits need to be isolated from feedback. In some cases, when a vehicle is remote started, feedback oc
Comments to this Manuals