Autostart AS-2775 User Manual

Notice The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of the product, be that either d

P. 10 Installation Guide the relay is activated, +12 volts from 87 is sent through 30, and the OEM trunk switch is activated, by the positive pulse.

Installation Guide P. 11 module's Trunk release output activates the relay. The ground signal is sent from 87 through 30 to the vehicle's Tr

P. 12 Installation Guide 5-pin Secondary Harness (a.k.a. the secondary harness) This harness has the remaining wires used in basic remote starter ins

Installation Guide P. 13 6 VIOLET (+) Door pin input This input should be used in vehicles that use a positive-switching Dome Light circuit. Connect t

P. 14 Installation Guide (Also known as the “wait-to-start light”.) The purpose of the Glow-plug circuit on diesel vehicles is to pre-heat the Combus

Installation Guide P. 15 compatibility and functionalities). 5 Pager Port Is used to connect an optional AS-200P pager (to use this option, make sure

P. 16 Installation Guide Manual or Automatic Transmission This module may be installed on vehicles with manual or automatic transmissions. It is orig

Installation Guide P. 17 2. Before the lights go out, press and hold the brake pedal and then press one of the following buttons: LOCK ...

P. 18 Installation Guide OPTION 2* Ignition valet ENABLED MENU 3 * INDICATES DEFAULT SETTING FEATURE 1 – Home Valet OPTION 1 Home valet ENABLED O

Installation Guide P. 19 Multi-speed Tach Programming 1. Enter programming mode (see on page 15) ⎯ the parking lights will stay on for up to 20 second

P. 2 Installation Guide Table of ContentsIntroduction ... 2 Included in the Kit ...

P. 20 Installation Guide Clutch Bypass In order to remote start a manual transmission vehicle, the clutch switch must be bypassed. Clutch safety switc

Installation Guide P. 21 modules connected to the G.O. Wire, a relay (and diodes) may have to be added to strengthen the negative current going to

P. 22 Installation Guide ¾ Standard Secure Lock: If this Option is selected, upon receiving a remote START signal, secure lock will unlock the doors

Installation Guide P. 23 Flashing LED To gain access to this feature, make sure the Flashing LED option has been enabled at the time of programming

P. 24 Installation Guide If the vehicle has a manual transmission, Idle Mode can be activated through the same routine as that used for Ready Mode (se

Installation Guide P. 25 If Safe Start is enabled, you can activate Cold Weather Mode by: • Pressing and releasing the START button, then; • Pres

P. 26 Installation Guide • To put the system o u t o f Valet mode using the TRANSMITTER (Remote Valet Mode): a. Press the UNLOCK and START butt

Installation Guide P. 27 transmitter, and to unlock the other doors, if desired, by pressing the UNLOCK button for a second time. The output will p

P. 28 Installation Guide To set the system to Ready Mode: If Ready Mode is enabled by remote If Ready Mode is enabled by handbrake 1. Ensure that al

Installation Guide P. 29 5. To save the new settings: press LOCK and UNLOCK. If 3 chirps are returned, the new settings have been saved Resetting t

Installation Guide P. 3 Included in the Kit Before beginning the installation, please review the Installation Guide —particularly the Wiring Diagram a

P. 30 Installation Guide  Starter kill option. Sit inside the vehicle with all doors closed. Arm the vehicle, then try to start the engine with the

Installation Guide P. 31 Diagnostics – Parking Light Flash Table Flashes Description 1 • Doors locked, starter kill armed. • Run time has expir

P. 32 Installation Guide Troubleshooting Q & A The following are some common installation-related issues. A problem or symptom is given and then p

Installation Guide P. 33 • Do you have the correct OEM disarm wire? • Did you program the disarm wire? 11. The ABS and the CHECK ENGINE light co

P. 34 Installation Guide 25. I blow fuses every time I try the remote door locks and I have already installed a relay. • Door locks are reverse pola

P. 4 Installation Guide ♦ When wiring in parallel, make sure to isolate each connection with a diode in order to avoid feedback and possible damage.

Installation Guide P. 5 Installation Order The following is a suggested order for the Installation procedure. It is intended as a guide for novices, t

P. 6 Installation Guide when the module is in the vehicle. The fuses on the power wires should be removed during the pre-wire stage. The fuses will n

Installation Guide P. 7 A basic introduction to the Relay What is a relay? A device that responds to a small current or voltage change by activating s

P. 8 Installation Guide quenching/suppression diode, and that the Negative trigger is on the same terminal of the relay as the Anode (+ or non-stripe

Installation Guide P. 9 Problem: Some vehicle circuits need to be isolated from feedback. In some cases, when a vehicle is remote started, feedback oc